Brasilian Chair
Cymo 15
Figo FG 19
Figo FG K9
Figo FG 20
Figo Air KN
Tango TG 23
Tango TG 24
Tango ESDS 24
Tangolino
Panamero PM
Tango 23 ESDS
Figo Air 1N
NK 1
Lezgo 71
Lezgo 72
Lezgo 73
Lezgo 74
Lezgo Air
Lezgo 7k
Löffler Plus
Work Around The Clock
Ergo
Ergo FA
Ergo FK
Ergo VK
Aogo
Aogo VK
Sedlo
Sedlo FA
Sedlo FK
Sedlo RL
Sedlo VK
Sit as far back as possible to ensure your back is supported by the backrest.
Adjust armrests for a relaxed arm position, without raising your shoulders.
Keep the angle between your upper and lower legs greater than 90°.
An upright sitting position is essential for proper configuration of your swivel chair. Sit as far back as possible to ensure your back is supported by the backrest. Configuring the height of the seat depends on whether you work at a height-adjustable desk or not. Here are some rough guidelines: Adjust armrests for a relaxed arm position, without raising your shoulders. Keep the angle between your upper and lower legs greater than 90°.
To adjust the seat height, pull the lever on the right-hand side underneath the seat upwards. Apply or release pressure on the seat to raise or lower it to your preferred height. Once you’ve found the desired height, release the lever to lock the seat in place.
The height of the backrest can be adjusted to eight different positions. Release the pressure on the backrest and use both hands to gradually push it up. Once it reaches the highest position, it will reset to the lowest. The backrest should support the area between the first and fifth lumbar vertebrae, just above waist height. Note that the backrest height on the Lezgo Air and Brasilian Chair models cannot be adjusted.
Adjust the backrest pressure using the rotary handle located on the right-hand side underneath the seat. Turn the handle forward to increase pressure or backward to decrease it. For optimal dynamic seating, set the synchro mechanism's restoring force according to your body weight. The chair's synchronous motion sequence with changing sitting postures works best when the restoring force is properly adjusted. This ensures the motion is effortless and the backrest provides enough support to prevent you from falling backward.
You can adjust the backrest tilt between 80° and 125° and lock it in five positions within this range. Apply or release pressure on the backrest to find your desired angle. To lock the position, hold the backrest in place and turn the rotary handle on the left-hand side under the seat one position backward. To release the lock, turn the handle back to the starting position (one turn forward) and lean on the backrest. The locking mechanism will release with an audible click.
You can adjust the seat depth by pulling the handle and sliding the seat forward or backward with your pelvis. Once you've found the desired seat depth, release the handle to lock it in place. To reset the seat to its default setting, pull the lever and remove all pressure from the seat. Please note that seat depth adjustment is not available for the Arthrodesis seat (Löffler plus).
Adjust the armrest height by pressing the button on the inside of the armrests. While holding the button, move the armrests to your preferred position. Release the button once you reach the desired height. Ensure that when sitting upright, your forearms are almost fully supported by the armrests.
You can also adjust and lock the distance between the armrests. To do this, push the lever on the underside of the armrests down until it points towards the ground. Move the armrests either closer to or farther from the seat. To lock the position, return the lever to its original position.
In addition to height and width adjustments, these multifunctional armrests offer extra features: The armrest pad can be moved forwards and backwards in 20 mm increments. Additionally, the armrest pad can be swiveled left and right in 15° increments.
To activate the ERGO TOP fixation, first remove pressure from the seat. Turn the lever on the right-hand side under the seat upwards to lock it. To enable ERGO TOP, turn the lever downwards. Please note that the ERGO TOP fixation feature is not available on the Brasilian Chair model.
